Biphasic Meter DWG Block for AutoCAD

Biphasic Meter DWG Block for AutoCAD

Biphasic meter – Court – Views

Drawing labels, details, and other text information extracted from the CAD file (Translated from Spanish):

mts, The wall should be fixed by means of lead plugs. long, use bare wire no. copper awg for ground descent, the switch will be set in the same way, kwh meter, must invariably tax, galvanized thick wall conduit mm., use protector for grounding, staple for earth connection, of ground iron galvanized copper tube of mm. by mts of length must be separated minimum mts. of the gas pipes never connect these, for mm tube by means of lead plugs mm long screws. place a staple every cm., mts, cms, cms., The wall should be fixed by means of lead plugs. long, use bare wire no. copper awg for ground descent, the switch will be set in the same way, kwh meter, must invariably embody, galvanized thick wall conduit mm., mts, use protector for grounding, staple for earth connection, of ground iron galvanized copper tube of mm. by mts of length must be separated minimum mts. of the gas pipes never connect these, mts, the switch will be set in the same way, galvanized thick wall conduit mm., for mm tube by means of lead plugs mm long screws. place a staple every cm., the switch can go in the interior a distance no greater than linear meters, eye of mm long mm., thick wall conduit, isolate roll similar iusa, galvanized wire no., held, cms, cms., weather of mm., preparation for socket-type meter in phase service up to connected load kw, the future must be attached to the neutral while it is phase service, must invariably embody, this bridge will be removed when connecting the phase service, neutral, Earth, phase, the load: the neutral does not carry fuse must be continuous with jumper attached to the neutral of the load., neutral wound wound to neutral of user with

Raw text data extracted from CAD file:

4.80 mts 1.80 mts \A1;La base de enchufe se debe fijar a la pared mediante taquetes de plomo y tornillos de 38.1 mm. (1 \S1#2;\H1.429x;'' ) de largo Utilizar alambre desnudo No. 8 AWG de cobre para la Bajada a Tierra 5 El interruptor se fijará en la misma forma Medidor de KWH Deberá enbonar invariablemente \A1;Tubo Conduit Galvanizado pared Gruesa de 32.1 mm. (1\S1#4;'' ) 5 Utilizar protector para la bajada a tierra Grapa para conexion a tierra \A1;Varilla de Tierra Copperweld, fierro galvanizado, tubo de cobre galvanizado de 12 mm. (1\S1#2;'') por 1.30 mts de largo y deberá estar separada minimo 0.5 mts. de las tuberias de gas y nunca conectarse a estas \A1;Grapa "U" para tubo de 32.1 mm / , instala_ do mediante taquetes de plomo y tornillos de 38.1 mm (1\S1#2;'') de largo. Colocar una grapa cada 50 cm. 1.80 mts 4.80 mts 5 cms 50 cms. F1 F2 N F3 F1 F2 N F3 \A1;La base de enchufe se debe fijar a la pared mediante taquetes de plomo y tornillos de 38.1 mm. (1 \S1#2;\H1.429x;'' ) de largo Utilizar alambre desnudo No. 8 AWG de cobre para la Bajada a Tierra El interruptor se fijará en la misma forma Medidor de KWH Deberá embonar invariablemente \A1;Tubo Conduit Galvanizado pared Gruesa de 32.1 mm. (1\S1#4;'' ) 1.80 mts Utilizar protector para la bajada a tierra Grapa para conexion a tierra \A1;Varilla de Tierra Copperweld, fierro galvanizado, tubo de cobre galvanizado de 12 mm. (1\S1#2;'') por 1.30 mts de largo y deberá estar separada minimo 0.5 mts. de las tuberias de gas y nunca conectarse a estas 4.80 mts El interruptor se fijará en la misma forma \A1;Tubo Conduit Galvanizado pared Gruesa de 32.1 mm. (1\S1#4;'' ) \A1;Grapa "U" para tubo de 32.1 mm d, instala_ do mediante taquetes de plomo y tornillos de 38.1 mm (1\S1#2;'') de largo. Colocar una grapa cada 50 cm. El interruptor puede ir en el interior a una distancia no mayor de 5 metros lineales \A1;Perno ojo de 304.8 mm. (12'') de largo 15.875 mm. (\S5#8;'') d \A1;Tubo conduit galvani_ zado de pared gruesa de 32.1mm. (1\S1#4;\H1.429x;'') Aislar rollo similar a IUSA P 1341 Alambre galvanizado Nº. 12 Alambre galvanizado Nº. 12 Retenida 5 cms 50 cms. (20'') \A1;Mufa intemperie de 32 mm. (1\S1#4;'') d PREPARACION PARA MEDIDOR TIPO SOCKET EN SERVICIO DE 127/220 VOLTS, 2 FASES Y NEUTRO, HASTA 15 KW DE CARGA CONECTADA La futura F-2 deberá de estar unida al neutro mientras es servicio de fase 1 Deberá embonar invariablemente Este puente se retirará al conectar el servicio a 2 fase F1 F2 N F1 F2 NEUTRO A TIERRA FASE 1 A LA CARGA: El neutro no lleva fusible deberá ser continuo con puente y/ o unido al neutro de la carga. Neutro corrido ó entorchado al neutro del usuario (aislado con cinta).

Language	Spanish
Drawing Type	Block
Category	Mechanical, Electrical & Plumbing (MEP)
Additional Screenshots
File Type	dwg
Materials
Measurement Units
Footprint Area
Building Features	Car Parking Lot
Tags	autocad, block, court, DWG, electrical standards, electricity, elektrischen normen, meter, normes électriques, padrões elétricos, views